(410) 677-4975
Used - Roof flashing cover with a dormered Cape Cod home

What Is Roof Flashing and Why Does It Fail? A Guide for Pittsville, MD Homeowners

By : Guillermo Molina Matus

Most homeowners think about shingles when they picture a roof. But another material does just as much to keep water out: roof flashing. Knowing what flashing is, where it goes and why it fails can save you from a costly water damage repair.

This guide is for homeowners in Pittsville, Salisbury and across Wicomico County, where fall storms and humid summers put extra stress on every part of a roof.

Used - Step flashing where a dormer wall meets the shingle roof, photographed by G and Bros on a home in Salisbury, Maryland

Where Flashing Lives on Your Roof

Flashing is thin metal, usually galvanized steel or aluminum, that roofers install wherever two roof surfaces meet or where the roof meets a wall, chimney, vent or skylight. Water follows gravity, and these joints are exactly where it tries to sneak in.

Where flashing goes on a typical roof

Chimney flashing Step flashing at a wall Pipe boot Drip edge along the eaves

Illustration. The gold lines mark where flashing seals the roof.

  • Chimney flashing: seals the gap between the chimney and the roof.
  • Step flashing: runs in steps along the side of a dormer or wall where it meets the roof slope.
  • Valley flashing: lines the channel where two roof slopes meet.
  • Pipe boots: wrap around plumbing vent pipes that come through the roof.
  • Drip edge: runs along the eaves and rakes to guide water off the edge.
Used - Side wall of a dormer meeting the shingle roof, where step flashing keeps water out, on a home G and Bros worked on in Salisbury, Maryland

Why Flashing Fails on Eastern Shore Roofs

Homes in Pittsville and the rest of Wicomico County deal with high humidity, heavy summer storms, nor’easters and freeze-thaw cycles in winter. All of that wears flashing down faster than in drier places.

  • Rust and corrosion. Galvanized steel eventually rusts, especially where water sits at the joints. Once rust takes hold, the seal fails.
  • Sealant failure. Caulk and roofing cement at the seams crack and pull away under sun and temperature swings. A gap as thin as a credit card can let water in.
  • Wind. Strong storm winds can work poorly fastened flashing loose over the years.
  • Poor installation. Flashing is one of the most skill-dependent parts of a roof. Shortcuts on step flashing can create a leak that does not show up for a year or two.
Used - Shingle roof meeting vinyl siding below a window, a joint sealed by flashing, on a home G and Bros inspected in Salisbury, Maryland

Signs Your Flashing May Be Failing

  • Water stains on ceilings or walls near a chimney, dormer or skylight
  • Rust streaks running down from flashing onto the shingles
  • Lifted, bent or missing metal at roof transitions
  • Cracked or missing sealant at chimney corners or vent boots
  • Soft roof decking near a chimney, a sign of long-term leaking

If you spot any of these, the next step is a roof inspection. What looks like a small flashing issue from the ground can involve water damage to the decking underneath.

Repair or Replace? What We Look At

Not every flashing problem needs a full replacement. We check whether the metal is still sound or corroded through, whether the shingles around it were damaged and whether the problem is in one spot or part of a bigger installation issue.

When we do a roof repair in Pittsville, Cambridge or anywhere in Wicomico County, we check the whole flashing system while we are on the roof, not just the spot that is leaking. Nearby sections often show early signs of the same problem.

Used - Dormer on a shingle roof seen from above, with flashing along its sides, on a home G and Bros worked on in Salisbury, Maryland

Frequently Asked Questions

How long does roof flashing last?

Quality aluminum or galvanized steel flashing can last a couple of decades or more when it is installed well and kept sealed. In our humid climate, expect the lower end of that without regular inspections.

Can I seal flashing myself with caulk from the hardware store?

A roofing-grade sealant can buy time in an emergency, but hardware-store caulk is not a permanent fix. It breaks down quickly in sun and cold. A proper repair uses the right metal and the right overlap with the shingles.

Does homeowners insurance cover flashing repairs?

It depends on the cause. Storm damage from wind or hail is often covered. Wear and age usually are not. Photograph the damage as soon as you notice it.

What does a flashing repair cost?

It depends on where the flashing is, how much needs to be replaced and whether any decking was damaged. An on-site inspection is the only way to give an accurate number.

Is it safe to put off a flashing repair until spring?

It is risky. Wet winter weather gives water more chances to get in, and once it reaches the decking you may be facing rot or mold on top of the flashing repair.

Seeing signs of a flashing leak?

G and Bros is GAF Certified Plus, family-owned since 2012, with 25+ years of Maryland roofing experience from our founder. We work in Pittsville, Salisbury, Cambridge and across the Eastern Shore.

Get a Roof Quoteor call 410-677-4975

Used - G and Bros Services Pictures. 109 Clark St Salisbury MD 21804 Local Roofing Contractor in the Salisbury Area. Commercial Roofing Company. Residential Roofing Company. Shingle Roof Repair Shingle Roof Replacement TPO Roof Repair TPO Roof Replacement EPDM Roof Repair EPDM Roof Replacement Metal Roof Repair Metal Roof Replacement
Share to...